NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instructi
STEP 2 (See Diagram 2) A.) Attach the Upper Frame (#1) onto the two Guide Rods (#17). Secure it with two M10 x ¾” Allen Bolts (#103) and ∅ ¾” Washe
STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#2) to the Upper Frame (#1). Secure it with one 6 ¾” Front Press Base Axle (#29), two Ø
DIAGRAM 3 11
STEP 4 (See Diagram 4) A.) Attach the Seat Pad (#88) to the Seat Post (#6). Secure it with two M8 x 1 5/8” Allen Bolts (#113) and Ø 5/8” Washers
DIAGRAM 4 13
STEP 5 (See Diagram 5) A.) Slide the Right Butterfly (#10) onto the right axle on the Butterfly Base (#13). B.) Insert the Butterfly Handle (#9) into
STEP 6 (See Diagram 6 & Upper Cable Loop Diagram) A.) Attach the 167” Upper Cable (#42) to the opening on the front of Upper Frame (#1). Make
DIAGRAM 6 16
Upper Cable Loop Diagram 17
STEP 7 (See Diagram 7 & Lower Cable Loop Diagram) A.) Attach the 217” Lower Cable (#40) to the opening on the Leg Developer (#8). Attach a Pu
TABLE OF CONTENTS BEFORE YOU BEGIN... 1 IMPORTANT SAFETY NOTIC
DIAGRAM 7 19
Lower Cable Loop Diagram 20
STEP 8 (See Diagram 8 & Butterfly Cable Loop Diagram) A.) Clip one end of the 83” Butterfly Cable (#41) to the open slot on the Right Butterfl
22
Butterfly Cable Loop Diagram 23
STEP 9 (See Diagram 9) A.) Connect the Lat Bar (#24) to the 167” Upper Cable (#42) with two Hooks (#90) and one Short Chain (#75). B.) Attach the Ab
STEP 10 (See Diagram 10) A.) Attach one end of 75” Hip-Thigh Cable (#39) to the bracket on the Rotating Cam Plate (#32). Secure it with one M10 x 1”
Hip-Thigh Cable Loop Diagram 26
STEP 11 (See Diagram 11) A.) Snap the bottom of the two Weight Stack Covers (#46) onto the Weight Stack Cover Base (#68) previously installed in Step-
WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Low Pulley 20 30 40 50 60 70 80 90 100 Lat Pull 30 40 50 60 70 80 90 100 110 Butt
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a p
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Upper Frame 1 61 5 3/8” Grip 6 2 Front Press Base 1 62 Ø 1” End Cap 4 3
IMPEX® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under norma
WARNING LABEL REPLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or ille
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
HARDWARE PACK 6
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended this machi
DIAGRAM 1 8
Kommentare zu diesen Handbüchern