Impex MWM 1801 Bedienungsanleitung

NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction Pa

STEP 4 (See Diagram 4) A.) Attach the Left Vertical Beam (#4) to the Left Base Frame (#3). Secure it with two M10 x 2 ½” Carriage Bolts (#82),

DIAGRAM 4 10

STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#15) to the Left Base Frame (#3). Secure it with a M10 x 9 ¼” Axle (#50), two ∅ ¾” Washers

STEP 6 (See Diagram 6) A.) Insert the axle on the Left Butterfly (#12) through the hole on the Left Upper Frame (#11) from the bottom up. Slide a

Cable Loop Diagram for Butterfly Station 13

Cable Loop Diagram for Bench Press Station 14

STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the two Swivel Pulley Brackets (#42) to the Left Upper Frame (#11). Secure each Bracket w

STEP 8 (See Diagram 8 & Cable Loop Diagram) A.) Attach a Chain (#51) to the Left Vertical Beam (#4). Secure it with one M10 x 1 3/8” Allen Bolt

STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach one end of the140” Leg Press Cable (#28) to the opening hole on the Left Seat Support (

DIAGRAM 9 18

TABLE OF CONTENTS BEFORE YOU BEGIN...……….. 1 IMPORTANT SAFETY NOT

STEP 10 (See Diagram 10 & Cable Loop Diagram) A.) Attach the 114” Upper Cable (#26) to the front opening on the Right Upper Frame (#6). NOTE: Th

STEP 11 (See Diagram 11 & Cable Loop Diagram) A.) Attach the 39” AB Cable (#30) to the opening on the Right Vertical Beam (#2). Attach a Pulle

DIAGRAM 11 21

STEP 12 (See Diagram 12) A.) Now move the machine to its final position. After installing the weight stack, it will be too heavy to move. Check and

STEP 13 (See Diagram 13) A.) Insert one Foam Tube (#34) halfway through the hole on the Right Seat Support (#8). Insert one Foam Tube (#34) halfway

STEP 14 (See Diagram 14) A.) Attach a Backrest Board (#23) to the Left Vertical Beam (#4). Secure it with two M8 x 2 1/8” Allen Bolts (#84) and ∅

HOW TO USE How to use the quick release connector. The Clip is removed from the Connector. Connector Clip Place the chain in between the c

PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Right Base Frame 1 2 Right Vertical Beam 1 3 Left Base Frame 1 4 Left Vertical Beam 1 5 Guide Rod 4

MWM 1801 Weight Resistance Chart Weight Plate Station 1 2 3 4 5 6 7 8 9 Low Pulley 30 42 54 66 78 90 102 114 126 Lat Pull 31 42 53 64 75 86 9

IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal

IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a

HARDWARE PACK 3

HARDWARE PACK 4

ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended this mac

STEP 2 (See Diagram 2) A.) Attach the Right Vertical Beam (#2) to the Right Base Frame (#1). Secure it with two M10 x 2 ½” Carriage Bolts (#82),

STEP 3 (See Diagram 3) A.) Align four ∅ 2 ½” x 1” Rubber Bumpers (#68) to the holes on the Right Base Frame (#1). Insert four Guide Rods (#5) t

DIAGRAM 3 8